Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal
Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal
Energy Seal Home page Elastomeric coatings products Elastomeric coatings specifications Contact Us Project Calculator

Roof Coating - Acu-Caulk:BG


DESCRIPTION
Acu-Caulk:BG is a 100% acrylic elastomeric, brush grade caulk used to bridge gaps in flashing, seams, fasteners and penetrations.

USES
For preparing fasteners, seams, penetrations, skylights, etc.

FEATURES
- Superior Protection - forms a durable, weather resistant "rubber-like" seal.
- Ideal for sealing holes, cracks and joints.
- Highly flexible.
- 100% acrylic elastomeric caulk, fully compatible with other Energy Seal Products.
- Superior adhesive and cohesive strength.
- Plasticizer-free caulk, will not dry-out or become brittle.
- Contains a strong mildewcide / fungicide.
- Easy to use, easy clean up, non-toxic and VOC compliant water based caulk.

PREPARATION
All surfaces to be coated must be clean, dry and free of any oil, grease or dirt. High pressure water washing is recommended. Any existing coating must be checked for good adhesion. Before application, any loosely adhered coating must be removed and bare surfaces must be prepared, cleaned and checked for compatibility.

APPLICATION
Acu-Caulk:BG is ready to use. Thinning is not required or recommended.

Brush: Good quality, stiff, synthetic bristle brush.
Putty Knife: 4 inch, flexible blade.

Material safety Data sheet
TECHNICAL DATA


This product conforms to ASTM-6083.

Roof Caulk
Acu-Caulk:BG
Product List
Acu-Caulk:BG Acu-Caulk:BG
Acu-Caulk:FG Acu-Caulk:FG
Acu-Fabric:SB Acu-Fabric:SB
Acu-Gloss Acu-Gloss
Acu-Prime All Acu-Prime All
Acu-Rust Prime Acu-Rust Prime
Acu-Shield Acu-Shield
Acu-Shield:Ceramic Acu-Shield:Ceramic
Acu-Tac Acu-Tac
Property
ASTM
Result
Color:
White
Viscosity:
D 562
Min. 145 KU @ 25ºC / 77ºF
Density:
D 1475
11.53 ± .1 lbs./gal.
PH:
>8.8 ± .5
Percent Solids:
D 2697
47.6% ± 2% by volume
D 1644
62.0% ± 2% by weight.
Flash Point:
Same as water.
Tensile Strength:
D 2370
135 lb/in2 @ 25ºC / 77ºF at Max Stress
Elongation:
D 2370
200% @ 25ºC / 77ºF
Flexibility:
D 522
Pass (-5°C) After 1000 hours accelerated weathering
Permeability:
D 1653
5
Fungi Resistance:
G 21
Zero Growth
Coverage:
5 gallons will cover 125 lineal feet, 6 inches wide.
Recommended Coverage: As needed.
Min. Surface Application Temp.:
7.2ºC / 45ºF. Do not allow to freeze.
Drying Time:
6 hours @ 25ºC / 77ºF, 50% relative humidity; to sustain foot traffic.
Packaging:
5 gallon buckets.
CAUTION:
Do not apply within two hours of sunset, rain, fog or freezing temperatures. All coatings must be completely dry before exposing to water or foot traffic. Keep all containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call Physician immediately.

Our technical data and suggestions are based on information from laboratory and field testing which we believe to be reliable and correct. However, the accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either expressed or implied. Since the use of the material is beyond manufacturer's control, buyer assumes all risk whatsoever as to their use or results obtained. We guarantee our products conform to Advanced Coating Systems, Inc. quality control. Advanced Coating Systems warrants only the standard quality of material. Advanced Coating Systems' sole responsibility shall be to replace that portion of our product, which proved to be defective. Installer is reponsible to test adhesion and product compatibility with substrate prior to application.
 

Copyright © 2005 Advanced Coating Systems, Inc. All Rights Reserved

Powered by Professional Web Hosting - Affordable Web Design by Primeaus.com