Roof Coating - Acu-Gloss
|
|
DESCRIPTION
Acu-Gloss is an elastomeric clear coat. Intended as a protective finish coat for our Acu-Shield elastomeric roof coating.
USES
High gloss finish coat to help keep our topcoat systems clean longer. Can also be used on masonry, concrete and other mechanically sound surfaces where a high gloss is desired.
FEATURES
- Extremely tough, durable, UV resistant protective sealant.
- Excellent water resistance.
- Good bridging qualities over hairline cracks and small openings.
- Excellent adhesion and binding qualities.
- Outstanding resistance to dirt collection and pollutants.
- Keeps surface clean thereby reducing maintenance costs.
- Brings out and heightens the natural color of stone and brick.
- Environmentally safe.
PREPARATION
All surfaces to be coated must be clean, dry and free of any oil, grease or dirt. Pressure washing is recommended. Any existing coating must be checked for good adhesion. Before application, any loosely adhered coating must be removed and bare surfaces must be prepared, cleaned and checked for compatibility.
APPLICATION
Acu-Gloss is ready to use. Thinning is not required or recommended.
Spray: Airless Sprayer, 1/2 g.p.m. capacity with a #517 tip.
Brush: Good quality synthetic bristle brush.
Roller: Long nap roller.
 Material safety Data sheet
TECHNICAL DATA
 This product conforms to ASTM |
 |
Acu-Gloss |
|
| Property |
ASTM |
Result |
| Color: |
 |
White, dries clear. |
| Viscosity: |
D 562 |
95 - 105 KU @ 25ºC / 77ºF |
| Density: |
D 1475 |
8.55 ± lb/gal. |
| PH: |
|
>8.0 ± 0.5 |
| Percent Solids: |
D 2697 |
32% ± 2% by volume. |
|
D 1644 |
32% ± 2% by weight. |
| Flash Point: |
|
Same as water. |
| Elongation: |
D 2370 |
1200% at break. |
| Tensile Strength: |
D 2370 |
252 lb/in2 |
| Flexibility: |
D 522 |
Pass (-5°C) After 1000 hours accelerated weathering |
| Fungi Resistance: |
G 21 |
Zero growth |
| Coverage: |
|
250 sq.ft. per gallon depending on the porosity of the surface. |
| Recommended Coverage: |
|
The number of coats depends on surface porosity; however, one coat is needed. |
| Min. Surface Application Temp.: |
|
7.2ºC / 45ºF. Do not allow to freeze. |
| Drying Time: |
|
Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat must be thoroughly dry before applying second coat. |
| Packaging: |
|
5 gallon buckets, 50 gallon drums. |
|
 CAUTION:
Do not apply within two hours of sunset, rain, fog or freezing temperatures.
All coatings must be completely dry before exposing to water or foot traffic.
Keep all containers covered when not in use. Dispose of all containers
in accordance with state and local environmental regulations. Keep away
from children. If ingested, DO NOT induce vomiting. Call Physician immediately.
Our technical data and suggestions are based on information from laboratory and field testing which we believe to be reliable and correct. However, the accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either expressed or implied. Since the use of the material is beyond manufacturer's control, buyer assumes all risk whatsoever as to their use or results obtained. We guarantee our products conform to Advanced Coating Systems, Inc. quality control. Advanced Coating Systems warrants only the standard quality of material. Advanced Coating Systems' sole responsibility shall be to replace that portion of our product, which proved to be defective. Installer is reponsible to test adhesion and product compatibility with substrate prior to application. |
| |
|
|
|
