Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal
Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal Energy Seal
Energy Seal Home page Elastomeric coatings products Elastomeric coatings specifications Contact Us Project Calculator

Roof Coating - Acu-Prime All


DESCRIPTION
Acu-Prime All is a durable clear primer for most non-rusted or non-metal surfaces. Acts as an intermediate coat between difficult to adhere substrates and topcoat.

USES
Concrete, masonry surfaces (all kinds), galvanized metal, previously painted metal, aluminum, asphalt, rubber and plastic.

FEATURES
- Superior adhesion to various substrates.
- Bonds to unstable substrates.
- Provides a tough, adhesive, durable film.
- Quick drying time.
- Environmentally safe.
- Easy to use, easy clean up, non-toxic and VOC compliant water based coating.

PREPARATION
All surfaces to be coated must be clean, dry and free of any oil, grease or dirt. High pressure water washing is recommended. Any existing coating must be checked for good adhesion. Before application, any loosely adhered coating must be removed and bare surfaces must be prepared, cleaned and checked for compatibility.

APPLICATION
Acu-Prime All is ready to use. Thinning is not required or recommended.

Spray: Airless Sprayer, 1/2 g.p.m. capacity with a #517 tip.
Brush: Good quality Nylon Polyester or Nylon bristle brush.
Roller: Short nap roller.

Material safety Data sheet
TECHNICAL DATA

This product conforms to ASTM

Acu-Prime All
Acu-Prime All
Product List
Acu-Caulk:BG Acu-Caulk:BG
Acu-Caulk:FG Acu-Caulk:FG
Acu-Fabric:SB Acu-Fabric:SB
Acu-Gloss Acu-Gloss
Acu-Prime All Acu-Prime All
Acu-Rust Prime Acu-Rust Prime
Acu-Shield Acu-Shield
Acu-Shield:Ceramic Acu-Shield:Ceramic
Acu-Tac Acu-Tac
Property ASTM Result
Color: White, dries clear.
Viscosity:
D 562
85 - 90 KU @ 25ºC / 77ºF
Density:
D 1640
9.4 ± .1 lb/gal
PH: >8.0 ± .5
Percent Solids:
D 2697
21% ± 2% by volume.
D 1644
31% ± 2% by weight.
Flash Point: Same as water.
Tensile Strength: - n/a -
Elongation: - n/a -
Coverage: 250 square feet per gallon.
Recommended Coverage: 1 - 2 coats @ 3 - 6 mils. Depending on surface porosity.
Min. Surface Application Temp.: 7.2ºC / 45ºF. Do not allow to freeze.
Drying Time: 3 hours @ 25ºC / 77ºF, 50% relative humidity.
Packaging: 5 gallon buckets, 50 gallon drums.
CAUTION:
Do not apply within two hours of sunset, rain, fog or freezing temperatures. All coatings must be completely dry before exposing to water or foot traffic. Keep all containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call Physician immediately.

Our technical data and suggestions are based on information from laboratory and field testing which we believe to be reliable and correct. However, the accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either expressed or implied. Since the use of the material is beyond manufacturer's control, buyer assumes all risk whatsoever as to their use or results obtained. We guarantee our products conform to Advanced Coating Systems, Inc. quality control. Advanced Coating Systems warrants only the standard quality of material. Advanced Coating Systems' sole responsibility shall be to replace that portion of our product, which proved to be defective. Installer is reponsible to test adhesion and product compatibility with substrate prior to application.
 

Copyright © 2005 Advanced Coating Systems, Inc. All Rights Reserved

Powered by Professional Web Hosting - Affordable Web Design by Primeaus.com