Elastomeric coating | Acu-Tac

Roof Coating - Acu-Tac

DESCRIPTION
Acu-Tac All is a durable clear primer for most non-rusted or non-metal surfaces. Acts as an intermediate coat between difficult to adhere substrates and topcoat.

USES
Asphalt, concrete, wood, tile, metal and virtually any clean, dry, non-silicone surface.

FEATURES
- Seals asphaltic surfaces with little or no bleed through.
- Superior primer for hard to coat surfaces such as asbestos roofing.
- Prevents premature aging and leaks in roofing.
- Excellent adhesion to various surfaces.
- Easy to use, easy clean up, non-toxic and VOC compliant water based coating.

PREPARATION
All surfaces to be coated must be clean, dry and free of any oil, grease or dirt. High pressure water washing is recommended. Any existing coating must be checked for good adhesion. Before application, any loosely adhered coating must be removed and bare surfaces must be prepared, cleaned and checked for compatibility.

APPLICATION
Acu-Tac is ready to use. Thinning is not required or recommended.

Spray: Airless Sprayer, 2 g.p.m. capacity with a #517 tip.
Brush: Good quality synthetic bristle brush.
Roller: Long nap roller.

Material safety Data sheet
TECHNICAL DATA

This product conforms to ASTM

Acu-Tac


	Acu-Caulk:BG
	Acu-Caulk:FG
	Acu-Fabric:SB
	Acu-Gloss
	Acu-Prime All
	Acu-Rust Prime
	Acu-Shield
	Acu-Shield:Ceramic
	Acu-Tac

Property	ASTM	Result
Color:		Blue clear
Viscosity:	D 562	55-60 KU @ 25ºC / 77ºF
Density:	D 1475	8.38 ± .1 lbs./gal.
PH:		>8.0 ± .5
Percent Solids:	D 2697	46% ± 2% by volume.
	D 1644	48% ± 2% by weight.
Flash Point:		Same as water.
Tensile Strength:	D 2370	100 lb/in² @ 25ºC / 77ºF at max. stress.
Elongation:	D 2370	1675% @ 25ºC / 77ºF
Permeability:	D 1653	5
Coverage:		200 sq.ft. per gallon depending on the porosity of the surface.
Recommended Coverage:		The number of coats depends on surface porosity; however, one coat is needed.
Min. Surface Application Temp.:		7.2ºC / 45ºF. Do not allow to freeze.
Drying Time:		Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat must be thoroughly dry before applying second coat.
Packaging:		5 gallon buckets, 50 gallon drums.

CAUTION:
Do not apply within two hours of sunset, rain, fog or freezing temperatures. All coatings must be completely dry before exposing to water or foot traffic. Keep all containers covered when not in use. Dispose of all containers in accordance with state and local environmental regulations. Keep away from children. If ingested, DO NOT induce vomiting. Call Physician immediately.

Our technical data and suggestions are based on information from laboratory and field testing which we believe to be reliable and correct. However, the accuracy and completeness of said tests are not guaranteed and not to be construed as a warranty, either expressed or implied. Since the use of the material is beyond manufacturer's control, buyer assumes all risk whatsoever as to their use or results obtained. We guarantee our products conform to Advanced Coating Systems, Inc. quality control. Advanced Coating Systems warrants only the standard quality of material. Advanced Coating Systems' sole responsibility shall be to replace that portion of our product, which proved to be defective. Installer is reponsible to test adhesion and product compatibility with substrate prior to application.